riskfriday2

Dual Fuel Range Cooker With 13amp Plug Are you a home cook who appreciates the flexibility of gas cooktops but still requires an oven to bake in? Find a dual-fuel range cooker that offers the best of both worlds. Gas cooktops are the preferred choice of many home chefs with expertise in the kitchen due to their superior temperature control. best dual fuel range cookers uk permit them to use advanced cooking techniques such as grilling. These powerful stoves are costly particularly if they need an additional gas connection and an electrician to install them. What is a 13amp plug? If you have a dual fuel range cooker (also called an electric and gas oven) then you'll require an appropriate 13 amp plug. The plug will also need to be wired in the cooker circuit using a competent electrician. This ensures that the current flowing through the plug doesn't exceed the safe limit that could result in an electrical fire. The plug has an electrical fuse that regulates the current. The fuse goes out whenever the current passes through it beyond its capacity. This safeguards the appliance from overload of electricity. The fuse is rated 13 amps, as shown on top of the plug. This is the maximum amount of current that the plug could carry without damaging the appliance or causing heat to the socket. It is important that when replacing fuses you always use the same rated amperage as the original. You run the risk of overheating the socket if you replace a fuse that has a different rating. Ceramic 13 amp fuses are extremely robust and can withstand high temperatures from an oven. The ceramic element is also fire-proof, making it a more suitable choice than other types of fuse. There are several ways to install an 13 amp plug. It may be wired to an existing live socket and the flex then connected to this by an screw or a plastic jaw type cord clamp. The cord clamp should be tightened after the plug has been tightly pushed into place. Some plugs include a wiring diagram on cardboard over the pins. These should be removed before connecting the wires. It is essential that the wires are cut to the correct length as leaving them too long can cause them to break when the plug cover is replaced. The earth wire should be the longest in order to connect it before the neutral and line pins. How do I connect a 13amp plug? The vast majority dual cookers that use fuel in the UK are equipped with a 13 amp plug. This is important because ovens can draw large amounts of current, while standard plug sockets only have a 10 amp rating. In general new appliances should include a plug at the point-of-sale. This is to comply with the Plugs and Sockets etc. (Safety Regulations) 1994. Older appliances might not have a plug and this is the reason for the problem. When connecting the cooker to an existing plug socket the first step is to make sure that the rating of the fuse in the box is in line with the plug's rating. This is important since a fuse that is not properly sized can be dangerous. It is also advisable to ensure that the fuse is installed in the cartridge and there isn't any movement within it. The next step is to prepare the flex to be used. Remove the sheathing to reveal the three conductors insulated. Use a utility blade to nick the sheathing just beyond the grip on the cord at the entry point of the plug. The blade will not penetrate the insulated conductors. The nick should be wide enough to allow the sheathing and cable to separate as the sheathing is pulled back. Cut off the excess sheathing leaving about 40mm beyond the flex. This flex is placed over the plug and the earth terminal is placed at the top and live and neutral terminals at the bottom. The sheathing around each pin is removed using the coloured conductors as a guide. The internal cable is then secured into the terminal using the cord grip. If the plug is fitted with a screw type cord clamp loosen it, and then pull back the insulation to reveal the copper conductors. Connect each insulated conductor to the appropriate terminal (starting with the earth first, then neutral and finally the live) using the channel they run through in the plug. What is the maximum current draw of a plug with 13amps? The maximum power draw of an 13amp plug is 3kw at 230 volts. This is a lot of power, however the standard fuse that comes with the UK plugtop won't fail until the cable reaches a hazardous temperature. A defective plug or socket may result in a fire, so it's important to be vigilant about how much power you use particularly in the kitchen. The ceramic fuses used in plugtops weigh around 25mm and are rated for mains voltage of 240V. They'll have an BS kitemark or similar mark on the side and will contain sand. Glass or plastic alternatives are available, but they should not be used in conjunction with a live plug. Most dual fuel range cookers in the UK need to be hard-wired and will not plug directly into an outlet on the wall. They are typically connected through a dedicated cooker circuit, that is only suitable for appliances using up to 20 amps. Check the ring circuit of your home with the fuse box, or call a local electrician. Ask them if the sockets are on the same ring or if they are distinct. They should also be able tell you if there is a separate circuit to power your oven. If you're in the market for a brand new dual fuel range cooker, the size of your kitchen is a vital factor to take into account. We have a wide range of cookers that can be adapted to any space. Choose from compact 50-60cm dual-fuel models or vast 90cm+ double ovens from leading brands like Rangemaster and StovesAreUs. We also have a broad variety of multifunction gas and electric cookers. These versatile machines let you cook a variety of meals including curries, pasta, and casseroles! Explore our complete range of Cookers in Currys online or head in-store to browse. We offer free installation at home and delivery on a selection of range cookers, as well as flexible payment options. If you have any questions, our team are available to assist send us an email or give us a call. Credit is subject to status, and terms and condition apply. What is the maximum current draw of a cooker switch? There is a lot of confusion regarding the maximum current draw of the cooker switch. The reality is that the majority of cookers aren't made to plug into the standard socket, but instead are wired hard and fed into an oven ring circuit. This is because they typically consume more than 20 amps of power each time the electric oven and gas hob are being used. You will not find dual fuel range cookers that can be fitted in standard sockets, since this could pose an enormous fire risk and would violate electrical regulations. A licensed electrician must always install new electrical wiring in the kitchen to a cooker. They will also make sure that the load of the oven and hob does not exceed the circuit's supply capacity. My Home Page mix the flexibility of a gas stove with the precision and accuracy of an electric oven. They are therefore popular with both home cooks and chefs. Dual fuel range cookers are perfect for trying out different cooking techniques, including searing or charcoaling. When purchasing a new range cooker you will need to consider a number of factors like size, performance and cost. Additionally, you'll also need to make sure that your house has an appropriate gas hook-up to the appliance. If you're not sure, it is best to hire an appointment with a Gas Safe engineer to inspect your property before installation. The Currys range of dual fuel range cookers offers options to suit a variety of budgets, from affordable models from Indesit and Zanussi to our own exclusive Essentials collection. If you're looking for something a bit more sophisticated We also have a variety of top JennAir ranges, featuring many unique features. It is important to read the owner's guide before purchasing a dual-fuel range cooker. This will provide specific information about the electrical and gas requirements. You will require a gas connection in your home. A plumber may be required to set it up for you. It is also possible to require a dedicated cooker-ring circuit, installed by a qualified electrical engineer.